Volume 42 Issue 5
Oct.  2021
Turn off MathJax
Article Contents
Yu Cansheng, Zhang Longchao, Zheng Zhiwang, Gong Hui, Zhang Dafu. Effect of annealing temperature on microstructure and mechanical properties of vanadium microalloyed 780 MPa cold rolled dual phase steel[J]. IRON STEEL VANADIUM TITANIUM, 2021, 42(5): 158-163. doi: 10.7513/j.issn.1004-7638.2021.05.024
Citation: Yu Cansheng, Zhang Longchao, Zheng Zhiwang, Gong Hui, Zhang Dafu. Effect of annealing temperature on microstructure and mechanical properties of vanadium microalloyed 780 MPa cold rolled dual phase steel[J]. IRON STEEL VANADIUM TITANIUM, 2021, 42(5): 158-163. doi: 10.7513/j.issn.1004-7638.2021.05.024

Effect of annealing temperature on microstructure and mechanical properties of vanadium microalloyed 780 MPa cold rolled dual phase steel

doi: 10.7513/j.issn.1004-7638.2021.05.024
  • Received Date: 2021-08-11
  • Publish Date: 2021-10-30
  • The vanadium microalloyed tested steel was heated to 780 ℃, 800 ℃, 820 ℃ and 840 ℃, respectively and then held for a few minutes, followed by different cooling modes such as slow cooling, rapid cooling, simulated galvanizing, and air cooling to room temperature. Microstructure observation by SEM shows that microstructure uniformity is poor during annealing at 780 ℃ and undissolved carbides are found, leading to a weak combination of strength and plasticity. With the increase of annealing temperature, the size and fraction of ferrite gradually decrease, the volume fraction of mid-low temperature transformation products gradually increases and its size becomes coarser. When the annealing temperature was 800 ℃, the fraction of martensite reaches the maximum. When the annealing temperature further increases, the fraction of martensite decreases, while the fraction of bainite increases, resulting in a relatively stable tensile strength when annealing temperature of 800 ~840 ℃ range, however, the elongation firstly increases and then decreases. When the annealing temperature was 820 ℃, the steel strip obtains better mechanical properties. The yield strength, tensile strength, yield ratio, elongation after fracture A80 and hole expansion rate are 486 MPa, 835 MPa, 0.58, 16.0% and 27%, respectively.
  • loading
  • [1]
    Wang Li, Zhu Xiaodong, Zhang Pijun, et al. Lightweight automotive and advanced high-strength steel plates[J]. Baosteel Technology, 2003,(5):53−59. (王利, 朱晓东, 张丕军, 等. 汽车轻量化与先进的高强度钢板[J]. 宝钢技术, 2003,(5):53−59. doi: 10.3969/j.issn.1008-0716.2003.05.014
    [2]
    Lu Jiangxin, Wang Li. Production and use of high strength automobile steel plates[J]. Automobile Technology and Materials, 2004,(2):1−6. (陆匠心, 王利. 高强度汽车钢板的生产与使用[J]. 汽车工艺与材料, 2004,(2):1−6. doi: 10.3969/j.issn.1003-8817.2004.02.001
    [3]
    Bao Chengren, Li Zhong, An Zhe. Effect of cooling rate for continuous annealing on microstructure and properties of galvanizing dual phase steel[J]. Heat Treatment of Metals, 2010,35(1):103−105. (鲍成人, 李众, 安哲. 连续退火冷却速率对热镀锌双相钢组织性能的影响[J]. 金属热处理, 2010,35(1):103−105.
    [4]
    Ma Mingtu, Shi M F. Advanced high strength steel and it’s applications in automobile industry[J]. Iron and Steel, 2004,39(7):68−72. (马鸣图, Shi M F. 先进的高强度钢及其在汽车工业中的应用[J]. 钢铁, 2004,39(7):68−72. doi: 10.3321/j.issn:0449-749X.2004.07.018
    [5]
    Tang Di, Mi Zhenli, Chen Yulai. Technology and research and development of advanced automobile steel abroad[J]. Iron and Steel, 2005,40(6):1−5. (唐荻, 米振莉, 陈雨来. 国外新型汽车用钢的技术要求及研究开发现状[J]. 钢铁, 2005,40(6):1−5. doi: 10.3321/j.issn:0449-749X.2005.06.001
    [6]
    Kang Yonglin, Kuang Shuang, Yin Xiandong, et al. Research on progress and development[J]. Automobile Technology & Material, 2006,(5):1−5. (康永林, 邝 霜, 尹显东, 等. 汽车用双相钢板的开发与研究进展[J]. 汽车工艺与材料, 2006,(5):1−5. doi: 10.3969/j.issn.1003-8817.2006.05.001
    [7]
    Zhao Zhengzhi, Niu Feng, Tang Di, et al. Microstructure and properties of ultra-high strength cold-rolled dual phase steel[J]. Journal of University of Science and Technology Beijing, 2010,32(10):1287−1291. (赵征志, 牛枫, 唐荻, 等. 超高强度冷轧双相钢组织与性能[J]. 北京科技大学学报, 2010,32(10):1287−1291.
    [8]
    Fang Gang, Ma Mingtu, Dongun Kim, et al. Three kinds of strength level of DP steel formability[J]. Engineering Sciences, 2014,(1):66−70. (方钢, 马鸣图, Dongun Kim, 等. 三种强度级别的双相钢成形性能的研究[J]. 中国工程科学, 2014,(1):66−70. doi: 10.3969/j.issn.1009-1742.2014.01.009
    [9]
    雍岐龙. 钢铁材料中的第二相[M]. 北京: 冶金工业出版社, 2006.

    Yong Qilong, The second phase in steel materials[M]. Beijing: Metallurgical Industry Press, 2006.
    [10]
    Zhang Xuehui, Zhu Guohui, Mao Weimin. Effect of interaction between recrystallization and transformation on microstructure of dual phase steel[J]. Iron & Steel, 2009,44(9):86−89. (张学辉, 朱国辉, 毛卫民. 再结晶和相变的交互作用对双相钢组织特征的影响[J]. 钢铁, 2009,44(9):86−89. doi: 10.3321/j.issn:0449-749X.2009.09.020
    [11]
    赵征志, 郗洪雷, 梁江涛, 等. 600 MPa级热镀锌双相钢性能优化[J]金属热处理, 2016, 44(3), 110-113.

    Zhao Zhengzhi, Xi Honglei, Liang Jiangtao, et al. Microstructure and Properties optimization of 600 MPa hot dipping DP steel[J]. Heat Teartment of Metals, 2016, 44(3), 110-113.
    [12]
    邝春福, 郑之旺, 王礞. 退火温度对590 MPa级热镀锌双相钢组织与性能的影响. [J]金属热处理, 2016, 41(5), 133-136.

    Kuang Chunfu, Zheng Zhiwang, Wang Meng. Effect of soaking temperature on microstructure and properties of 590 MPa grade hot-dip galvanized dual phase steel. [J]. Heat Teartment of Metals, 2016, 41(5), 133-136.
    [13]
    Huang Qunfei, He Yanlin, Luo Juanjuan, et al. Effect of different volume fraction of martensite on deformation behavior of dual phase steels[J]. Iron & Steel, 2009,44(4):60−63. (黄群飞, 何燕霖, 罗娟娟, 等. 马氏体体积分数对双相钢变形行为的影响[J]. 钢铁, 2009,44(4):60−63. doi: 10.3321/j.issn:0449-749X.2009.04.014
  • 加载中

Catalog

    通讯作者: 陈斌, bchen63@163.com
    • 1. 

      沈阳化工大学材料科学与工程学院 沈阳 110142

    1. 本站搜索
    2. 百度学术搜索
    3. 万方数据库搜索
    4. CNKI搜索

    Figures(4)  / Tables(4)

    Article Metrics

    Article views (207) PDF downloads(46) Cited by()
    Proportional views
    Related

    /

    DownLoad:  Full-Size Img  PowerPoint
    Return
    Return