Mo-Ti高强钢强度波动原因分析

梁文; 吴润; 刘志勇; 陶文哲; 陈吉清; 谭佳梅

doi:10.7513/j.issn.1004-7638.2015.01.016

留言板

尊敬的读者、作者、审稿人, 关于本刊的投稿、审稿、编辑和出版的任何问题, 您可以本页添加留言。我们将尽快给您答复。谢谢您的支持!

姓名

邮箱

手机号码

标题

留言内容

验证码

Mo-Ti高强钢强度波动原因分析

doi: 10.7513/j.issn.1004-7638.2015.01.016

1. 武汉科技大学材料与冶金学院, 湖北武汉 430081;
2. 武钢研究院, 湖北武汉 430080;
3. 武钢股份 CSP 分厂, 湖北武汉 430083

详细信息

作者简介:
梁文(1982-),男,湖南娄底人,博士,主要从事含Ti高强钢及耐蚀钢的研发。

中图分类号: TF76
计量
- 文章访问数: 12
- HTML全文浏览量: 4
- PDF下载量: 1
- 被引次数: 0
出版历程
- 收稿日期: 2014-06-18

Cause Analysis on Strength Fluctuation of High-strength Steel with Mo-Ti

1. College of Materials and Metallurgy, Wuhan University of Science and Technology, Wuhan 430081, Hubei, China;
2. Research & Development Center of Wisco, Wuhan 430080, Hubei, China;
3. CSP Branch of Wisco Co., Wuhan 430083, Hubei, China

摘要

摘要: 采用金相检测、能谱分析等方法,对Mo-Ti高强钢强度波动的原因进行了研究,结果表明:卷取温度设定过高和板宽方向温度不均匀是造成Mo-Ti高强钢强度波动的主要原因。0.12%Ti-0.10%Mo高强钢的最佳析出温度为570℃,Mo元素能促使含Ti钢中生成大量细小而弥散的第二相(Mo_xTi_1-x)(C_yN_1-y),这些纳米级的第二相能产生强烈的析出强化效果。通过下调卷取温度以及采取层流冷却边部遮挡等措施,得到了抗拉强度800 MPa、强度均匀的高强钢。
- Mo-Ti高强钢 /
- 强度波动 /
- 析出温度
Abstract: The cause of strength fluctuation of Mo-Ti microalloyed high-strength steel was investigated by metallography observation and energy spectrum analysis. The results showed that strength fluctuation was mainly caused by higher coiling temperature and the inhomogeneous temperature profile through width direction. Thepeak precipitation temperature of the high-strength steel with 0.12Ti-0.10Mo（%） was about 570 ℃. Mo could promote a large amount of second phase （Mo_xTi_1-x）（C_yN_1-y） precipitates in Ti microalloyedsteel,and the dispersive and nano-size second phase could yield strong precipitation strengthening effect. By lowering the coiling temperature and adopting the edge-masking technology in the laminar cooling line,the high-strength steel with tensile strength more than 800 MPa and homogeneous strength was obtained.
- Mo-Ti microalloyed high-strength steel /
- strength fluctuation /
- precipitation temperature