钛微合金化对22MnB5汽车用钢组织及性能的影响

王功; 季国顺

doi:10.7513/j.issn.1004-7638.2021.01.025

钛微合金化对22MnB5汽车用钢组织及性能的影响

doi: 10.7513/j.issn.1004-7638.2021.01.025

王功^1,,
季国顺²

1.
江海职业技术学院机电汽车学院，江苏扬州 225101
2.
杭州电子科技大学机械工程学院，浙江杭州 310018

基金项目: 国家自然科学基金（51405119）；江苏省机电重点专业建设支持项目（JS2017016）。

详细信息

作者简介:
王功（1969—），男，江苏高邮人，汉族，硕士，副教授，主要从事汽车技术研究。E-mail：caishanhan5398624@163.com

中图分类号: TF76
计量
- 文章访问数: 231
- HTML全文浏览量: 42
- PDF下载量: 16
- 被引次数: 0
出版历程
- 收稿日期: 2020-01-16
- 刊出日期: 2021-02-10

Effect of titanium on microstructure and properties of steel 22MnB5 for automobile

Wang Gong^1
,,
Ji Guoshun²

1.
School of Electromechanical and Automobile, Jianghai Polytechnic College, Yangzhou 225101, Jiangshu, China
2.
School of Mechanical Engineering, Hangzhou Dianzi University, Hangzhou 310018, Zhejiang, China

摘要

摘要: 在22MnB5钢中添加不同含量的合金元素钛，制备了钛微合金化汽车用钢试样，并进行了试样显微组织、力学性能和耐腐蚀性能的测试与分析。结果表明：添加合金元素钛，有利于细化试样的内部晶粒、提高试样的力学性能和耐腐蚀性能。随钛含量从0逐渐增加至0.08%，试样内部晶粒先细化后粗化，其抗拉强度和屈服强度均先增大后减小、断后伸长率先增大后减小再增大、腐蚀电位先正移后负移，汽车用钢的力学性能和耐腐蚀性能均先提高后下降。试样钛含量优选为0.06%。与不添加钛相比，当钛含量添加至0.06%时试样的抗拉强度增加24 MPa、屈服强度增加27 MPa、腐蚀电位正移95 mV。
- 汽车用钢 /
- 22MnB5 /
- 微合金化 /
- 钛含量 /
- 力学性能 /
- 耐腐蚀性能
Abstract: The titanium microalloyed automobile steel samples were prepared by adding different content of titanium into 22MnB5 steel, and then the microstructure, mechanical properties and corrosion resistance of the samples were tested and analyzed. The results show that the addition of titanium is beneficial to refine the internal grain of the samples and improve the mechanical properties and corrosion resistance of the samples. With the increase of titanium content from 0 to 0.08%, the tensile strength and yield strength of the samples firstly increase and then decrease, the elongation after fracture firstly increases and then decreases and increases again. The corrosion potential firstly shifts forward and then negatively, and the mechanical properties and corrosion resistance of the automobile steel firstly increase and then decrease. The titanium content of the sample is preferably at 0.06%. When 0.06%Ti is added, the tensile strength of resulted steel increases by 24 MPa, the yield strength increases by 27 MPa, and the corrosion potential shifts positively by 95 mV.
- automobile steel /
- 22MnB5 /
- microalloying /
- titanium content /
- mechanical property /
- corrosion resistance

HTML全文

图 1 拉伸试样尺寸(mm)

Figure 1. Geometry of tensile samples (mm)

下载: 全尺寸图片幻灯片

图 2 试样力学性能测试结果

Figure 2. Mechanical properties of test samples

下载: 全尺寸图片幻灯片

图 3 试样拉伸断口形貌SEM照片

Figure 3. SEM morphology of the fracture in samples after tensile test

下载: 全尺寸图片幻灯片

图 4 试样耐腐蚀性能测试结果

Figure 4. Corrosion testing results of the samples

下载: 全尺寸图片幻灯片

图 5 试样腐蚀试验后的表面形貌

Figure 5. Surface morphology of the samples after corrosion test

下载: 全尺寸图片幻灯片

图 6 试样显微组织

Figure 6. EBSD showing the microstructure of steels at various Ti contents

下载: 全尺寸图片幻灯片

表 1 试样化学成分

Table 1. Chemical compositions of the used steels

编号	w/%
编号	C	Si	Mn	Cr	B	Ti	Al	S	P	V
试样1	0.22±0.01	0.28±0.01	1.25±0.01	0.11±0.01	0.004±0.001	0	0.03±0.01	<0.002	<0.015	bal.
试样2	0.22±0.01	0.28±0.01	1.25±0.01	0.11±0.01	0.004±0.001	0.02	0.03±0.01	<0.002	<0.015	bal.
试样3	0.22±0.01	0.28±0.01	1.25±0.01	0.11±0.01	0.004±0.001	0.04	0.03±0.01	<0.002	<0.015	bal.
试样4	0.22±0.01	0.28±0.01	1.25±0.01	0.11±0.01	0.004±0.001	0.06	0.03±0.01	<0.002	<0.015	bal.
试样5	0.22±0.01	0.28±0.01	1.25±0.01	0.11±0.01	0.004±0.001	0.08	0.03±0.01	<0.002	<0.015	bal.

下载: 导出CSV

参考文献(8)

[1]	Li Min, Hao Yulin, Yao Shicong, et al. Early corrosion behavior of typical automotive steel sheets in neutral salt spray test[J]. Electroplating & Finishing, 2019,38(18):1015−1021. (黎敏, 郝玉林, 姚士聪, 等. 中性盐雾环境中典型汽车用钢的初期腐蚀行为[J]. 电镀与涂饰, 2019,38(18):1015−1021.
[2]	Li Gang, Guo Xiaojun, Wang Lianhai. Study on non-quenched and tempered steel C38 + N for automobile[J]. Special Steel, 2019,40(5):54−56. (李刚, 郭晓俊, 王连海. 汽车用非调质钢C38+N的研究[J]. 特殊钢, 2019,40(5):54−56. doi: 10.3969/j.issn.1003-8620.2019.05.014
[3]	Li Teng, Wu Xiaodong, Tang Bingyuan, et al. Hot deformation behavior and establishment of flow stress constitutive model of HG700 automobile beam steel[J]. Materials for Mechanical Engineering, 2019,43(12):67−70, 76. (李腾, 吴晓东, 唐彬袁, 等. HG700汽车大梁钢的热变形行为及流变应力本构模型的建立[J]. 机械工程材料, 2019,43(12):67−70, 76. doi: 10.11973/jxgccl201912013
[4]	Kong Wei, Shi Peng, Liu Zhonghua, et al. Full-process technical control of non-oriented silicon steel for new energy vehicles[J]. China Foundry Machinery & Technology, 2019,54(6):12−16. (孔为, 时鹏, 刘中华, 等. 一种新能源汽车用无取向硅钢的全流程工艺控制[J]. 中国铸造装备与技术, 2019,54(6):12−16. doi: 10.3969/j.issn.1006-9658.2019.06.002
[5]	Li Wei, Wang Kai. Influence of cold rolling reduction on microstructure of high temperature annealing for high manganese steel used for car lightweight[J]. Forging & Stamping Technology, 2019,44(11):164−169. (李伟, 王凯. 冷轧压下量对汽车轻量化用高锰钢高温退火组织的影响[J]. 锻压技术, 2019,44(11):164−169.
[6]	Hou Baohui, Song Yi, Wang Yunhao, et al. Design and application of fixture reserved for curved laser-welding automobile steel plates[J]. Shanghai Metals, 2019,41(6):103−108. (侯宝辉, 宋艺, 王云浩, 等. 曲线焊缝汽车钢板激光焊接专用夹具的设计和应用[J]. 上海金属, 2019,41(6):103−108. doi: 10.3969/j.issn.1001-7208.2019.06.019
[7]	Wang Yongjian, Zhang Yanmin, Wang Yaoli, et al. Composition design and microstructure analysis of titanium microalloyed new die steel[J]. Journal of Henan University of Science & Technology(Natural Science), 2019,40(5):1−6. (王永健, 张彦敏, 王要利, 等. 钛微合金化新型模具钢成分设计及组织性能分析[J]. 河南科技大学学报(自然科学版), 2019,40(5):1−6.
[8]	Liu Zhennan, Tao Dongping, Yao Chunling, et al. Phase equilibrium study and thermodynamic analysis on secondary refining process of titanium-microalloyed steel[J]. Journal of Iron and Steel Research, 2019,31(8):702−711. (刘振楠, 陶东平, 姚春玲, 等. 钛微合金钢炉外精炼相平衡研究与热力学分析[J]. 钢铁研究学报, 2019,31(8):702−711.