Comparative study on wear resistance of plastic die steels NAK80 and S136

Xie Yi; Xian Yong

doi:10.7513/j.issn.1004-7638.2021.04.024

Volume 42 Issue 4

Aug. 2021

Turn off MathJax

Article Contents

Article Navigation > IRON STEEL VANADIUM TITANIUM > 2021 > 42(4): 144-148

Xie Yi, Xian Yong. Comparative study on wear resistance of plastic die steels NAK80 and S136[J]. IRON STEEL VANADIUM TITANIUM, 2021, 42(4): 144-148. doi: 10.7513/j.issn.1004-7638.2021.04.024

Citation:

Xie Yi, Xian Yong. Comparative study on wear resistance of plastic die steels NAK80 and S136[J]. IRON STEEL VANADIUM TITANIUM, 2021, 42(4): 144-148. doi: 10.7513/j.issn.1004-7638.2021.04.024

Xie Yi, Xian Yong. Comparative study on wear resistance of plastic die steels NAK80 and S136[J]. IRON STEEL VANADIUM TITANIUM, 2021, 42(4): 144-148. doi: 10.7513/j.issn.1004-7638.2021.04.024

Citation:

Xie Yi, Xian Yong. Comparative study on wear resistance of plastic die steels NAK80 and S136[J]. IRON STEEL VANADIUM TITANIUM, 2021, 42(4): 144-148. doi: 10.7513/j.issn.1004-7638.2021.04.024

PDF( 868 KB)

Comparative study on wear resistance of plastic die steels NAK80 and S136

doi: 10.7513/j.issn.1004-7638.2021.04.024

Xie Yi^1
,,
Xian Yong^{2
,
,}

1.
School of Automotive Engineering, Chongqing Three Gorges Vocational College, Wanzhou 404000, Chongqing, China
2.
School of Materials and Environmental Engineering, Chengdu Technological University, Chengdu 611730, Sichuan, China

Received Date: 2021-06-26
Publish Date: 2021-08-10

Abstract

Abstract

The microhardness, microstructure, friction and wear behavior of pre-hardened plastic die steels NAK80 and S136 were studied. The results show that the microstructure of NAK80 steel consists of lath martensite and granular bainite, while that of S136 steel are ferrite matrix and fine carbides, and the microhardness is 405.01 ± 63 HV and 354.21 HV ± 6.14 HV respectively. The friction coefficients of NAK80 and S136 steel decrease with the increase of load. At 60N, the friction coefficients of NAK80 and S136 steel reach their lowest values (0.34 and 0.37). However, when the load increases to 80 N, the friction coefficient increases. Overall, the friction coefficient of S136 is higher than that of NAK80. The wear behavior of NAK80 has high load sensitivity under different load conditions while S136 has more stable wear resistance. At low load, abrasive wear and delamination wear are dominant, and the wear resistance of NAK80 is better than that of S136. At high load, adhesive wear and abrasive wear are dominant, and the wear resistance of S136 steel is better than that of NAK80.
- die steel,
- load,
- hardness,
- microstructure,
- wear resistance properties

FullText(HTML)

References(5)

References

[1]	Lv Chuanjiang, Wu Xiaochun. Research status and prospect of advanced mirror plastic mold steel[J]. Die & Mould Manufacture, 2017,17(10):93−98. (吕穿江, 吴晓春. 高级镜面塑料模具钢研究现状及展望[J]. 模具制造, 2017,17(10):93−98. doi: 10.3969/j.issn.1671-3508.2017.10.025
[2]	Zhang Xianming. Several kinds of new plastic mold steel properties and research of the heat treatment process[J]. Die & Mould Manufacture, 2015,15(5):83−86. (张先鸣. 几种新型塑料模具钢性能及热处理工艺的研究[J]. 模具制造, 2015,15(5):83−86. doi: 10.3969/j.issn.1671-3508.2015.05.025
[3]	Cai Wu. Comparative analysis on steel quality of typical plastic mold at home and abroad[J]. Special Steel Technology, 2018,24(1):8−12. (蔡武. 国内外典型塑料模具钢质量对比分析研究[J]. 特钢技术, 2018,24(1):8−12.
[4]	Zhang Kuan, Zhen Fan, Qu Jinbo. Effect of solution and aging treatment on microstructure and hardness of plastic mold steel NAK80[J]. Hot Working Technology, 2014,43(20):193−197. (张宽, 镇凡, 曲锦波. 固溶和时效处理对塑料模具钢NAK80组织和硬度的影响[J]. 热加工工艺, 2014,43(20):193−197.
[5]	Li Ainong, Zhou Dan, Zhao Yuhong, et al. Comparison for microstructure and properties of several pre-hardened plastic mould steels[J]. Materials for Mechanical Engineering, 2012,36(10):50−53. (李爱农, 周丹, 赵玉宏, 等. 几种预硬塑料模具钢的组织与性能对比[J]. 机械工程材料, 2012,36(10):50−53.